i aint got none of them programs like yall guys or a shop 2 take it to.6ut i drew up some shit 6y what i think MIGHT work.from a real nigga stand point tell me is it reasona6le. su6s.pointed up.
Spl SP210 10 SP2 Series DVC 4 Ohm Subwoofer - 1200W Max/500W RMS
* 1200 Watts Max Power/500 Watts RMS Power
* 110oz. Magnet
* Efficiency: 83dB
* Mounting Depth: 6.125
* Cutout Diameter: 9.25
usin my whole trunk.
1. 65 inches across wit 2 rows of five 10's(1ft) cu6e.
2. 7 inches deep (with a 6 inch lid?)
3.how 6ig should my vent to mouth 6e?an is it a such thing as 2 long a port to mouth?
my design i made up.not a master installer like yall cats,nor meets floridian standards.i just wanna kno will this work.

not worried 6out mounting amps in trunk or 6atteries eaither.

lol good luck tryin to get that box in the trunk and runnin 10 10's..i had 4 12's n it took up the whole trunk...u gotta remeba they width of your trunk is not all easy to get to for example the big lip that the trunk comes down and rests on..how do u expect to fit that box in there ? cut off the lips of the trunk n weld em back on or make 2 spearate boxes?if i was u id try to get back to 8 10's n u mite have enuff airspace but stilll doubt it...gbody trunks arent all that big and wit the hump up front that takes alot of room out too...but aye good look wit it homie

o and lookin at that drawing if that lil space between wat says speaker roof n base part is your opening for the air pressure...lol them speakers are gonna act like they got asthma wit no inhaler cuz that is def not enuff airspace to push out any kindaof pressure at all n will sound like oure shit and have absolutly no air pressure

damn trill nigga shit.aight so ill swollow my pride an do 8 10's. how tall should dat opening 6e for air space.
does the square ft an otha stuff look right? an speaker depth?

download this to draw a 3d version of your box design, takes a little use to but, it's the shit, an know it will not calculate how big your box is suppose to be or how long thd port should and etc... it's only a 3d sketch tool thats free, and download the regular one it's free the pro isn't
http://sketchup.google.com/download/

Man... forget the whole (8) 10's thing, you gotta gain a lil more experience first. Not being funny but it shouldn't take all this.

Lets go with (4) heavier 10's in a box like this (except you will be using (4) not 6.








We gone do with the AQ2200D amp with these subs:

http://www.onlinecarstereo.com/CarAudio/p_..._SWR-1022D.aspx

http://www.onlinecarstereo.com/CarAudio/p_...a_V-Max102.aspx

http://onlinecarstereo.com/CarAudio/p_2061...nics_B10D2.aspx

http://www.onlinecarstereo.com/CarAudio/p_..._07CVR10-4.aspx

http://www.onlinecarstereo.com/CarAudio/p_...TS-W1008D2.aspx



This would be built right behind the backseat. gone cut a hole in the backseat, a ll bigger than the port opening on the box. It will hang off the hump of the trunk a lil bit but you can build an amp rack and battery holder under that. less space taken up, less headache, and will bang right.

The entire box should be (max dimensions) 42" WIDTH x 13" HEIGTH x 24" DEPTH

Since this is 2 boxes in one, EACH box should be ~ 15" WIDTH x 13" HEIGHT x 24" DEPTH

That will give each sub right under 1cft after all displacements.

The middle "tunnel" area would be ~12" wide.

So you would cut a 14"H x 13" W hole in the middle of your backseat,

thanks


lol.manye i kno u gone get mad 6ut.how many inches is 0.6 cft.i thought 12x 12 was 1 cft. how deep should the cover over my su6s 6e.

^^^^^ EDITED MY POST LOOK UP ^^^^^

oh god

lol

i like it am im takin note.
the 1setup u gave me looked easier an thing a almost had it dwn packed.except the cover depth.i was up till 3 figurin out the 1st setup mayne.

last setup is easier. just do that.

i am.im just stuck on how deep the woofer cover should 6e.

Told you everything.

on the 10 up setup i missed dat.
i was askin how deep should da cover over the 8 10 setup 6e.so dat air will travel right.
hey how much you charge 2 tell me some descent measurements for the 8 10 facin up setup?