Adding a 6.5 component set to the rear side panels.
Then smoothing out the upper rear panels and fixing a few cracks then priming them.

Hard to tell, but this is what a panel looks like after it has been hit with an 80 grit 3" DA at 10pm......

One of the rear panels had a broken corner.
And it was in a place that would be seen easily. So I made a new corner.

Shaved seat belt holes incase you didn't notice.








Shaved the shifter handle off the column. Changing it to a Hurst console shifter.

After lunch, I will get some pics up here of the trunk.
I am a picture whore and take pics of everything.

nice work

Sub box/trunk build up section.




The car.........

Sub box start........

Got some resin on the box and got it all strengthened up so it will NOT flex at all.
Then got the side panels that will hold the amps started.

A frame for the drivers side........




















A frame for the passenger side....

Stretched, replaced, resined, matted, blah blah blah........

NICE NICE NICE NICE NICE

nice piocs!keep us posted

What size subs do you plan on running.?. My lil brother has an 84 Type T and a 86 MC SS and likes your work. He'd like to run 2 S10L7/CVX10's in a box similar to yours. How much would you charge if you were build 1 and slang it?

Are you the dude who called me and left the message?
Seriously, it would cost as much to ship as it would to make it.








And damn I ain't been on here in awhile.

I got some pics of the Regal to post up sometime.

Lets see if anyone looks in here.......



























Gauges trimmed up and AC vent holes made.......













And the headlight switch is flushed in.

Test fit.....














And the making of the trim panel under the steering wheel.........







Peice I cut out to slide over the column....






Trimmed to shape....

you still doin glass work on this ride. did the customer run out of money before so you stoped the project or does it take this long to do all of that work anyway lookin good so far

He ran outta money.
He was layed off for awhile, then got a job again, then layed off that.
Now he is working again so I am knocking the dust off it.

lmao did you use his dash as a note pad

Ok i got you

How much you chargin buddy for that dash?

Nice work though.

What would you charge to do this? I would ship you the dash

Nice work... i had been wondering how to sculpt the dash.. WOOO WWOOOOO SHIT! i think i got it now!

I AM curious too.. how much you charging dude for that dash?

check your pm im tryin to get a quote

nice stuff... too bad Rza, is such an asshole, i'd like to come over there and check you out!

The 2 center AC vents look like eyes with the radio spot as a mouth. We started messing around drawing on that and then it got outta hand.
The whole thing ended up a sketch board. It's all good now.

I don't wanna start throwing prices out there. It could vary in prices depending on how much you want to incorporate on the dash or how you want it finished. (paint or wrapped).

But I will tell ya this....... this dash got him a small discount in price since this is his 2nd car I did for him and he has another one lined up for the future.
But i can get the 2 of you a PM with a ballpark figure.

I got the PM. I been thinking about it and I have a plan.
PM coming back at ya.








Thanks. I appreciate all the feedback from everyone.

As for rza..... I have no control over that and you might have caught him on a bad day.
I am not sure what happen. But if you wanna PM me the detail I will look into it if you want.

What worries me about shipping something like that back to you is -- --

1..... cost of shipping due to weight and the oversized box that you would have to pay for.

2..... how will the box get treated during shipping? They don't know whats in there and would, toss, slide and probally kick the box on it's many stops.
Don't even think about someone dropping it.

Still interested? Where are you located? I will PM you a quote.

Not much to look at.
But it took some time getting the mounting holes at the top at the correct angles.
Then onto body working the whole thing.
Not sure if I took pics, but also got the steering column cover under the dash flushed in and body worked also.

Now onto the last thing I want to make for this dash.
It will be a cover panel for the head unit and the ac controls.
Started this last night and I should have stayed till the finish body work was complete, but I didn't want to finish routering while I was too tired.
I like all my fingers.

So it sits in flush and will have 45* angles routered around the inside of the openings.
This is where I left it...........

this is some good work...

Thanks.

Nice work Epic... i'd like to see some more pics of you doing the actual fleecin and glassin if you got any... you can send them pm or email, if want...

How long does this process take? Nice job and do u start jobs as u finish others or u focus on one job til its done....pm me a quote for a 85 cutlass dash with out paint.

also, what did you use, or how do you come up with templates to make dashes?